Skip to main content
Woodworking Machines >Briquette Machines >Falach 20XL Briquette Machine
IWM Soukup Cube 20 briquette machine with blue base, stainless steel drum, and control panel with start and stop buttons
  • IWM Soukup Cube 20 briquette machine with blue base, stainless steel drum, and control panel with start and stop buttons

    Falach 20XL Briquette Machine

    Falach ·Briquette & Wood Waste
    A compact, single-operator hydraulic press that turns dry shavings and dust into usable 30mm cube briquettes — eliminating skip costs without demanding significant floor space or a three-phase supply.

    Typically chosen by

    • Smaller joinery or timber workshops looking to eliminate skip costs by converting dry shavings and dust into usable briquettes
    • Businesses wanting a single-phase-compatible footprint where three-phase supply is limited or unavailable
    • Workshops producing waste at a manageable, consistent rate rather than high-volume batch production
    Get expert advice
    Book a free demo
    Before you commit

    Send us a sample - we’ll test your material first

    Not all waste streams briquette equally. Moisture content, particle size, and material mix all affect output quality and briquette consistency. We’ll run your material on the machine and report back before you make any decision.
    Book a free demo
    Request a material test

    Key specification considerations

    Press Capacity
    10–25 kg/hr
    At the upper end, this equates to roughly 200 g of briquette output per minute — suited to workshops with a steady but modest waste stream rather than high-volume continuous production.
    Electrical Supply
    3-phase, 16A (single-phase option available)
    The single-phase option uses the same 2.2 kW motor — confirm your workshop supply before ordering and discuss the single-phase variant with IWM if three-phase is not available.
    Weight
    233 kg
    Noise Level
    68 dB at operator position
    68 dB is broadly comparable to a normal conversation — no acoustic enclosure is typically required, though local workshop noise assessments should always be considered.
    See full specifications
    SpecificationValueNotes
    Dimensions (L × W × H)
    1250 × 740 × 1450 mm
    Allow additional clearance around all sides for hopper loading, briquette collection, and operator access — a practical envelope of at least 2.5 × 2 m is advisable.
    Weight
    233 kg
    Briquette Size
    30 × 30 × 30 mm
    Press Capacity
    10–25 kg/hr
    Hopper Volume
    0.75 m³
    Confirm this figure with IWM at point of enquiry — discuss your typical waste volume and throughput rate to ensure the hopper suits your workflow.
    Pump Motor Input
    2.2 kW
    Power Consumption
    1.1 kW/hr
    Electrical Supply
    3-phase, 16A (single-phase option available)
    The single-phase option uses the same 2.2 kW motor — confirm requirements with IWM at point of enquiry.
    Operation
    Continuous
    The machine runs continuously rather than in batch cycles, meaning it can feed into a consistent workflow without operator intervention between loads.
    Maximum Moisture Content
    15%
    Material above 15% moisture will produce inferior briquettes and may cause press issues — if your waste comes from a wet or green process, discuss pre-drying options with IWM.
    Specific Weight of Briquette
    900–1100 kg/m³
    This density range is comparable to softwood logs and makes the briquettes viable for most biomass appliances and log burners.
    Oil Cooler
    No
    No oil cooler is required at this capacity — the press is designed for continuous operation at its rated output without one.
    Briquette Collection
    Briquette chute and single bag stand supplied as standard
    The included chute and bag stand direct output straight into a collection bag — factor in space behind or beside the press outlet when planning your installation.
    Maximum Noise Level
    68 dB at operator position
    Get expert advice

    Is this the right
    machine for you?

    Choose the Falach 20XL Briquette Machine if...

    • Your workshop generates a modest, steady volume of dry shavings or dust — roughly enough to keep a 10–25 kg/hr press usefully occupied
    • Floor space is limited and you need a compact machine that can be positioned within a small production area
    • You need a single-phase option or have a 3-phase 16A supply readily available
    • You are new to briquetting and want a lower-commitment entry point before scaling up

    Consider an alternate model if...

    • Your waste volume regularly exceeds what a 25 kg/hr press can handle — the Falach 50XL (40–60 kg/hr) is likely a better specification
    • You are running a high-throughput operation where the lower capacity of this machine would create a bottleneck
    • Your ceiling height or headroom is restricted — the Falach 20 (H 1120 mm) offers the same footprint at a lower overall height and may be worth discussing with IWM
    • Your waste material frequently exceeds 15% moisture content, in which case pre-drying equipment or a different press specification should be considered
    Still not sure? We're happy to help
    Get expert advice
    Ready when you are

    Ready to improve your
    workshop's output?

    Book a specification call with one of our engineers. Thirty minutes, no obligation, plain English advice on what would actually work on your floor.

    Get expert advice
    Book a free demo

    Or call directly +44 (0)1636 918280