Skip to main content
Woodworking Machines > Shredders > Robust REUSER SD600 Shredder
Robust 60 industrial shredder machine in green and black with a large open feed hopper and drive motor
Technical engineering drawing of the Sico Drobilniki R60 ECO shredder showing multi-view orthographic projections with dimensions
Close-up of a carbide cutting insert secured by a central screw on the rotor of an industrial shredder
Close-up of a black perforated drum on a REUSER SD600 shredder with wood shavings and debris scattered below
Close-up view of a perforated metal grate inside the open chamber of a robust industrial shredder machine
A hand holding a pile of pale wood shavings above a large bed of the same shredded wood material.
  • Robust 60 industrial shredder machine in green and black with a large open feed hopper and drive motor
  • Technical engineering drawing of the Sico Drobilniki R60 ECO shredder showing multi-view orthographic projections with dimensions
  • Close-up of a carbide cutting insert secured by a central screw on the rotor of an industrial shredder
  • Close-up of a black perforated drum on a REUSER SD600 shredder with wood shavings and debris scattered below
  • Close-up view of a perforated metal grate inside the open chamber of a robust industrial shredder machine
  • A hand holding a pile of pale wood shavings above a large bed of the same shredded wood material.

    Robust REUSER SD600 Shredder

    Robust
    A single-rotor hydraulic shredder built for workshops and recyclers that need consistent, screenable output from bulky or mixed wood waste — with minimal operator intervention once running.

    Typically chosen by

    • Timber processors and pallet recyclers handling large or irregular wood waste that needs reducing to a defined particle size
    • Joinery and manufacturing workshops generating significant off-cut and reject volumes who need a robust, low-supervision shredding solution
    • Waste contractors and biomass fuel producers who need repeatable output granulation across varied wood feedstocks
    Get expert advice
    Book a free demo

    Key specification considerations

    Throughput
    Up to ~4 m³/h
    Actual throughput will vary with material density, moisture content, and screen size selected — treat this as a ceiling figure for planning purposes.
    Motor Power
    15 kW or 18.5 kW
    Both options require a three-phase supply; confirm available amperage and whether your incoming supply can support the star/delta start sequence before ordering.
    Output Granulation
    10 mm – ~30 mm (screen dependent)
    Screen hole size determines output particle size and directly affects throughput rate — smaller screens reduce capacity, so specify this based on your intended end use.
    Machine Weight
    ~1,250 kg
    Above 500 kg — floor loading capacity should be confirmed with your structural engineer or building surveyor before installation.
    See full specifications
    SpecificationValueNotes
    Motor Power
    15 kW or 18.5 kW
    Both options require a three-phase supply; confirm available amperage and whether your incoming supply can support the star/delta start sequence before ordering.
    Drive System
    Electric motor with reduction gear and belt transmission
    Motor Start Method
    Star/delta (star/triangle) system
    Star/delta starting reduces inrush current at start-up, which can be important if your site has supply capacity or tariff constraints around peak draw.
    Control System
    BOVER_BASIC intelligent control system
    Handles automated cycle control and overload protection — if the rotor stalls under load, the system reverses and re-attempts, reducing the need for manual intervention during a jam.
    Rotor Length
    ~550 mm
    Rotor Diameter
    ~222 mm
    Number of Cutting Knives
    14 knives
    Knife Design
    Hardened, four cutting edges per knife
    Four-edge knives can be indexed three times before replacement, which reduces consumable cost and downtime compared to single-edge designs.
    Cleaning Knives
    Hardened cleaning knives included
    Counter-Knives / Cutting Racks
    Hardened cutting racks included
    Sieve Material
    HARDOX wear-resistant steel
    HARDOX is a recognised wear-plate specification — relevant if you are processing abrasive or contaminated wood waste where standard sieves would wear prematurely.
    Screen / Hole Size
    10 mm – ~30 mm (configuration dependent)
    Screen size must be specified at order — discuss your end-use requirement (e.g. biomass chip spec, bedding material, or landfill diversion) with IWM before confirming.
    Throughput
    Up to ~4 m³/h
    Actual throughput will vary with material density, moisture content, and screen size selected — treat this as a ceiling figure for planning purposes.
    Feed / Hopper Opening
    939 mm × 567 mm
    Hopper opening determines the maximum cross-section of material you can feed in a single pass — oversized pieces will need pre-breaking before loading.
    Hydraulic Feed Unit
    Hydraulic pressure / pusher unit included
    The hydraulic pusher forces material into the rotor zone, reducing the need for manual feeding and allowing the machine to handle bulky or springy waste more consistently.
    Machine Dimensions (H × W × L)
    ~1,670 × 1,120 × 1,880 mm
    Allow additional clearance on all sides for extraction ducting, infeed access, and maintenance — this footprint alone is not sufficient for installation planning.
    Weight
    ~1,250 kg
    Above 500 kg — floor loading capacity should be confirmed with your structural engineer or building surveyor before installation.
    Noise Level
    Not published — contact IWM
    A confirmed noise level figure is needed to assess whether acoustic treatment or hearing protection zoning will be required in your facility; ask IWM for the test data when specifying.
    Certifications / Compliance
    Contact IWM for current documentation
    Confirm CE marking and any relevant machinery directive compliance with IWM at point of order, particularly if the machine is being integrated into a wider extraction or handling system.
    Get expert advice

    Is this the right
    machine for you?

    Choose the Robust REUSER SD600 Shredder if...

    • You are processing bulky, irregular or mixed wood waste at volumes that would overwhelm a smaller single-shaft machine, and need a robust hydraulic pusher to manage infeed consistently
    • Output particle size matters to your operation — for example, you are producing biomass chip to a specification, or separating material for reuse — and you need the flexibility of interchangeable screens
    • Knife longevity and reduced downtime are a priority: the four-edge knife design and HARDOX sieve are worth specifying when you are running the machine hard across shifts
    • You need a machine that can operate with minimal supervision and handle overload situations automatically via the BOVER_BASIC control system

    Consider an alternate model if...

    • Your volumes are lower or your waste stream is lighter and less variable — the Robust REUSER SD450 Wood Shredder is likely a better match and will cost less to run and maintain
    • You need a higher-capacity machine for a larger operation — the Robust REUSER SD700 Shredder steps up in throughput and should be discussed if you are regularly pushing the SD600 to its ceiling
    • You are processing smaller, more uniform offcuts rather than bulky or heterogeneous wood waste — the Robust SD90 or SD90 XL may be more appropriately sized and simpler to operate
    • Space is a significant constraint — at approximately 1,880 mm long and 1,250 kg, this machine requires a considered installation; confirm your floor loading and clearance requirements before ruling out a smaller model
    Still not sure? We're happy to help
    Get expert advice
    Ready when you are

    Ready to improve your
    workshop's output?

    Book a specification call with one of our engineers. Thirty minutes, no obligation, plain English advice on what would actually work on your floor.

    Get expert advice
    Book a free demo
    Or call directly +44 (0)7970461899