Skip to main content
Woodworking Machines > Timber Frame & SIP Machinery > Soukup Timber Frame Off Site Tilting Wing Table
Two angled timber frame tilting wing tables on blue steel frames, one showing dark panel surface, the other revealing internal wooden structure with clamps.
  • Two angled timber frame tilting wing tables on blue steel frames, one showing dark panel surface, the other revealing internal wooden structure with clamps.

Soukup Timber Frame Off Site Tilting Wing Table

Soukup
A fixed tilting assembly table for timber frame panel production where crane handling is not practical or not wanted. Built for volume output in permanent production halls, including those with restricted eaves height.

Typically chosen by

  • Timber frame manufacturers looking to reduce crane dependency and the delays that come with it
  • Offsite construction businesses building wall, floor, or roof panels at volume and needing to minimise dead time between assembly stages
  • Workshops operating in buildings with restricted eaves height, where standard panel-handling equipment cannot be used
Get expert advice
Book a free demo

Key specification considerations

Construction
Laser-machined steel profiles
Laser-machined profiles ensure consistent dimensional accuracy across the table surface, which matters when squareness is critical to panel assembly tolerances.
Crane Handling Required
No
Panels can be tilted and transferred without overhead lifting equipment, removing a common production bottleneck and reducing the need for crane access or certification on site.
Low-Height Hall Compatible
Yes
The table can be installed in production halls with restricted eaves height — worth confirming your specific clearance with IWM before specifying.
Panel Type Compatibility
Typical and atypical panels
Full accessory sets for non-standard panel configurations are available — these are shared with the Soukup Framer system, so compatibility should be confirmed if both machines are in use.
See full specifications
SpecificationValueNotes
Construction
Laser-machined steel profiles
Laser-machined profiles ensure consistent dimensional accuracy across the table surface, which matters when squareness is critical to panel assembly tolerances.
Design
Heavy industrial
Crane Handling Required
No
Panels can be tilted and transferred without overhead lifting equipment, removing a common production bottleneck and reducing the need for crane access or certification on site.
Low-Height Hall Compatible
Yes
The table can be installed in production halls with restricted eaves height — worth confirming your specific clearance with IWM before specifying.
Panel Type Compatibility
Typical and atypical panels (full accessory set)
Full accessory sets for non-standard panel configurations are available — these are shared with the Soukup Framer system, so compatibility should be confirmed if both machines are in use.
Standard Working Lengths
6 m, 9 m, 12 m (custom lengths available)
Working length should be matched to your longest panel type — confirm floor space and operator clearance requirements with IWM at the time of specifying.
Machine Weight & Power
Configured to order — contact IWM
Weight and power supply requirements vary with table length and configuration; IWM will confirm exact figures when specifying your installation.
Manufacturer
Soukup s.r.o., Czech Republic
Get expert advice

Is this the right
machine for you?

Choose the Soukup Timber Frame Off Site Tilting Wing Table if...

  • Your production line builds timber frame panels at volume and crane handling is creating delays or logistical constraints
  • You are working in a hall with limited eaves height where conventional panel-lifting equipment is not practical
  • You need a robust, permanently installed assembly table capable of handling both standard and atypical panel configurations
  • You are already running or specifying the Soukup Framer system and want compatible panel-handling downstream

Consider an alternate model if...

  • You need a flexible, reconfigurable assembly station rather than a fixed tilting table — the Soukup Framer Modular Assembly Table may be more appropriate
  • Your panel volumes are lower and a full tilting table is more infrastructure than your throughput justifies — discuss with IWM whether a simpler assembly solution fits better
  • You need integrated panel storage as part of your workflow — the Timber Frame Off Site Track Storage system should be considered alongside or instead
  • You are looking for cutting rather than assembly capability — the Soukup Crossline 650 or Crossline 500 address cross-cutting at the front end of the line
Still not sure? We're happy to help
Get expert advice
Ready when you are

Ready to improve your
workshop's output?

Book a specification call with one of our engineers. Thirty minutes, no obligation, plain English advice on what would actually work on your floor.

Get expert advice
Book a free demo
Or call directly +44 (0)7970461899